Retry Forever

Keeps long-running opencode sessions alive across transient provider failures.

If you leave a fleet of agents running for hours, a single upstream hiccup kills a whole session. opencode's built-in retry gives up after a handful of attempts, and then SessionRunner.drain throws:

level=ERROR message="Failed to drain Session" cause="AI.Error: RequestExecutor.execute: Provider request failed with HTTP 503"
level=ERROR message="Failed to drain Session" cause="AI.Error: RequestExecutor.request: getaddrinfo ENOTFOUND opencode.ai"
level=ERROR error.error="AI_RetryError: Failed after 3 attempts. Last error: Service Unavailable"

This plugin wraps globalThis.fetch — which is what opencode's request executor ultimately calls (effect/http/FetchHttpClient/Fetch defaults to () => globalThis.fetch) — so retries happen below the session runner. The session never learns that anything went wrong.

Install

mkdir -p ~/.config/opencode/plugin
curl -fsSL https://raw.githubusercontent.com/aryanranderiya/opencode-retry-forever/main/index.ts \
  -o ~/.config/opencode/plugin/retry-forever.ts

Or, once published to npm:

opencode plugin opencode-retry-forever -g

Per-project instead of global: drop the same file in .opencode/plugin/ inside the project. It loads on the next opencode start; opencode run --pure bypasses it.

Configuration

All optional, read from the environment at startup.

Variable	Default	Meaning
OPENCODE_RETRY_DELAY_MS	250	Fixed wait between attempts. No backoff, no growth. Set 0 for an immediate hot retry.
OPENCODE_RETRY_MAX_ATTEMPTS	0	0 means unlimited — retry until it gets through.
OPENCODE_RETRY_HONOR_RETRY_AFTER	1	Respect a Retry-After header when the server sends one. Turning this off is a good way to get rate limited harder.
OPENCODE_RETRY_MAX_RETRY_AFTER_MS	60000	Ceiling on how long a Retry-After may park you.
OPENCODE_RETRY_VERBOSE	1	Log every retry. Keep this on — an unlimited retry loop that logs nothing is indistinguishable from a hang.

What gets retried

• HTTP status: 408, 409, 425, 429, 500, 502, 503, 504, 520–525, 527, 529, 530.
• Thrown network errors, in both vocabularies that matter: Node/undici POSIX codes (ENOTFOUND, ECONNRESET, ETIMEDOUT, …) and Bun's own codes (ConnectionRefused, FailedToOpenSocket, DNSResolutionFailed, ConnectionClosed, ConnectionTimeout, IdleTimeout). opencode runs on Bun, and matching only the POSIX set silently misses every connect failure — the same blind spot that makes opencode's own retry give up on an unreachable provider.

Aborts are never retried: hitting Esc stops the loop immediately, including mid-wait. That guard is load-bearing, because a cancelled in-flight request can surface as ECONNRESET or terminated, both of which otherwise look retryable.

Request bodies are buffered once and replayed verbatim on every attempt, so Request objects and ReadableStream bodies survive a retry instead of failing as already-consumed.

Auto-resume: turns that die with an unknown finish reason

A transport retry cannot save a turn the provider ended mid-flight — the request succeeded, the stream opened, then stopped with finish: "unknown":

⚠ Retry attempt 2 scheduled: The provider response ended with an unknown finish reason.
⚠ Retry attempt 3 scheduled: The provider response ended with an unknown finish reason.
Error: Provider request failed with HTTP 503

opencode schedules a couple of retries and then gives up, taking the session with it. This plugin watches for that specific ending and re-sends the user's own prompt, indefinitely.

It only fires on a genuine drop. A turn that produced output and then stopped without a reason is a drop; a zero-token unknown finish is a deliberate abort — an interrupt, a denied permission, a compaction — and resending there would fight you.

Variable	Default	Meaning
OPENCODE_RESUME_PROVIDER	opencode-go	Provider to watch. * matches every provider.
OPENCODE_RESUME_MODEL	ox-alpha-free	Model prefix to watch. * matches every model.
OPENCODE_RESUME_DELAY_MS	3000	Wait before re-sending.
OPENCODE_RESUME_MAX_ATTEMPTS	0	0 means resend until the turn completes.

What does not get retried

• Failures mid-response-stream are handled by auto-resume above, not by the fetch retry: once the provider returns 200 and starts streaming, fetch has already resolved.
• Non-transient statuses (400, 401, 403, 404, …) pass straight through.

opencode 1.x vs 2.x

The plugin loads on both — the default export carries id, server (1.x) and setup (2.x). What runs differs sharply, because opencode 2.x never calls server at all, only setup:

	1.x	2.x beta
Fetch-level retry (503, DNS, resets)	works	inert — v2 keeps provider traffic away from the plugin's globalThis.fetch
Language-model retry	n/a	only for providers that register aisdk.hook("language")
Auto-resume	via the event hook	via event.subscribe() + session.prompt()

On 2.x the transport is simply not reachable from a plugin: session.hook("http.request") can mutate a request but never sees its response. Recovery therefore happens one level up, on session.execution.failed — the terminal event, raised once opencode's own retries are spent. A turn you stop yourself raises session.execution.interrupted instead, so resuming cannot fight an interrupt.

Verified against a provider that opens a stream, emits text, then dies with no finish chunk — 20 consecutive drops, which is well past opencode's own budget of about six turns:

	resumer disabled	enabled
provider turns	6	22
outcome	session dead	recovered on turn 21

Under 2.x, opencode runs a long-lived background service that loads plugins once at startup, so a plugin change is not picked up until opencode2 service restart.

License

MIT